Schneider VAMP 300 Series Protection and Control Relays

Schneider VAMP 300 Series Protection and Control Relays Suppliers, Exporters in India

Schneider VAMP 300 Series Protection and Control Relays are used for feeder, motor, generator and transformer protection in medium-voltage power systems. The range includes four main models: VAMP 300F, VAMP 300M, VAMP 300G and VAMP 300T.

Each model is meant for a specific application, while the main operating platform remains similar across the range. The relays handle protection, electrical measurements, breaker control, event recording and communication with SCADA or plant automation systems.

Optional arc flash protection can be added where fast fault detection inside the switchgear is required. It can be used in a new arc protection system or added to an existing VAMP arc flash setup.

Settings, logic, measurements and fault records can be accessed through VAMPSET software. Communication options vary by configuration and may include IEC 61850, Modbus, DNP3, IEC 60870 and Profibus.

Models Covered

• VAMP 300F – Feeder protection and control
• VAMP 300M – Motor protection and control
• VAMP 300G – Generator protection and differential protection
• VAMP 300T – Two-winding transformer protection

Specifications

• Product Name: Schneider VAMP 300 Series Protection and Control Relays
• Product Family: PowerLogic VAMP
• Relay Type: Numerical Protection and Control IED
• Available Models: VAMP 300F, VAMP 300M, VAMP 300G and VAMP 300T
• System Application: Medium-voltage power systems
• Protected Equipment: Feeders, motors, generators and two-winding transformers
• Protection Functions: Overcurrent, earth fault, voltage, frequency, thermal and differential protection, depending on the model
• Arc Flash Protection: Optional
• Arc Sensor Connection: Up to six point sensors, or one fibre loop with four point sensors, depending on configuration
• Arc Protection Trip Time: Down to approximately 2 ms in applicable arrangements
• Measurements: Phase and residual current, voltage, frequency, current imbalance, demand, power and energy
• Power Quality Functions: Harmonics up to the 15th order, current and voltage THD, voltage sag and voltage swell
• Control Functions: Local and remote control of switching devices
• Recording Functions: Up to 2,000 event records, fault values and disturbance records
• Communication: IEC 61850, Modbus TCP, Modbus RTU, DNP3, IEC 60870-5-101, IEC 60870-5-103, Profibus DP, SPA-bus and TCP/IP, depending on configuration
• Configuration Software: VAMPSET
• Local Connection: USB Type-B
• Mounting: Panel mounting

Features

• Separate models for feeder, motor, generator and transformer protection
• Overcurrent, earth fault, voltage and frequency protection
• Differential protection on VAMP 300G and VAMP 300T
• Optional high-speed arc flash protection
• Breaker control and status monitoring
• Electrical measurements from the relay front panel
• Event, fault and disturbance recording
• Harmonic, THD, voltage sag and voltage swell monitoring
• Programmable protection stages and control logic
• IEC 61850 and other communication options
• Settings and commissioning through VAMPSET
• Used for new panels, retrofit work and replacement of existing VAMP relays
• VAMP 300F Feeder Protection Relay

VAMP 300F is used for incoming feeders, outgoing feeders, overhead lines, underground cables and busbar sections. It handles the main protection and breaker control requirements of medium-voltage feeder panels.

Common installations include utility substations, industrial power systems, power plants, marine systems and offshore facilities.

VAMP 300M Motor Protection Relay

VAMP 300M is used for medium-voltage motors and motor feeder cables. It monitors motor current, thermal condition, electrical faults and operating status.

Optional RTD interface units can be used for motor winding and bearing temperature measurements. These values can also be sent to the plant automation system.

VAMP 300G Generator Protection Relay

VAMP 300G is used for generator differential protection, generator transformer protection and other generator protection duties. It is commonly applied to medium-sized generators rated up to approximately 150 MW.

An external RTD module can also be added where generator temperature monitoring is required.

VAMP 300T Transformer Protection Relay

VAMP 300T is used for two-winding power transformer protection. It covers differential, short-circuit, thermal overload, earth fault and voltage protection requirements.

It is commonly used in transformer protection panels, industrial substations, utility networks and power plants.

Applications

• Medium-voltage feeder panels
• Incoming and outgoing feeders
• Underground cable and overhead line protection
• Busbar sections
• Medium-voltage motors
• Motor feeder cables
• Generator protection panels
• Generator block transformers
• Two-winding transformers
• Utility substations
• Industrial substations
• Power generation plants
• Oil and gas facilities
• Cement and steel plants
• Mining operations
• Marine and offshore systems
• Water treatment plants
• Renewable energy projects
• VAMP relay replacement and retrofit work
• Schneider VAMP 300 Series Supplier and Exporter

We supply and export Schneider VAMP 300 Series protection relays for substations, industrial power systems, switchgear panels, power plants, EPC projects and maintenance requirements.